TGPForums.com

MODIFICATIONS => Performance => Topic started by: wildwildwest_11 on September 26, 2002, 11:54:17 AM

Title: 3.1 turbo hybrid in a 1990 chevrolet celebrity
Post by: wildwildwest_11 on September 26, 2002, 11:54:17 AM
Two Questions:
1. are there any sources for turbo 3.1 parts?
2. what are the major mechanical differences between a stock nat. asp. 3.1 and the turbo version, i.e computer, crank, timing ect.

i am considering converting my nat. asp. 3.1 to a turbo and when i foudn that GM, Mclearen and ASC already did it i figured why blow a motor when i can just use a "stock" setup.  ok thanks to all who post

Wildwildwest
Title: 3.1 turbo hybrid in a 1990 chevrolet celebrity
Post by: 90tgpblk on September 26, 2002, 06:37:55 PM
Jeff m would be the source for some of the best parts..  you can find his stuff on turbograndprix.com...  YES the turbo engine is different.... I don't know all the differences are but there many... I am sure some one here knows them all.... KCP
Title: here ya go
Post by: 1trucavalier on October 04, 2002, 11:14:30 AM
Engine:

3.1 L OHV Multi port fuel injected Turbocharged 60 degree V6  
SAE Net 205 horsepower, torque managed 225 lb-ft toque
8.8:1 Compression ratio
89mm bore x 84mm stroke
Garret T-25 turbo .62 A/R intake , .60 A/R exhaust w/ closed loop boost control and integrated waste gate.
Intercooled via Blackstone intercooler mounted left of radiator rear of A/C condenser
22lb/hr GM Multec Fuel Injectors
Hardened and rolled crankshaft
Forged Connecting Rods
Mahle Cast aluminum pistons w/ reinforcing steel ring
1.72 intake valve, 1.47 exhaust valve 2 valves per cylinder
Stock 3.1 Camshaft w/ flat hydraulic lifters
Water to oil cooler
High efficiency 3 row 17 fin per inch Blackstone Radiator
High Capacity Dual cooling fans
Title: Re: here ya go
Post by: Chris A on October 05, 2002, 07:07:20 AM
Quote from: 1trucavalierEngine:

3.1 L OHV Multi port fuel injected Turbocharged 60 degree V6  
SAE Net 205 horsepower, torque managed 225 lb-ft toque
8.8:1 Compression ratio
89mm bore x 84mm stroke
Garret T-25 turbo .62 A/R intake , .60 A/R exhaust w/ closed loop boost control and integrated waste gate.
Intercooled via Blackstone intercooler mounted left of radiator rear of A/C condenser
22lb/hr GM Multec Fuel Injectors
Hardened and rolled crankshaft
Forged Connecting Rods
Mahle Cast aluminum pistons w/ reinforcing steel ring
1.72 intake valve, 1.47 exhaust valve 2 valves per cylinder
Stock 3.1 Camshaft w/ flat hydraulic lifters
Water to oil cooler
High efficiency 3 row 17 fin per inch Blackstone Radiator
High Capacity Dual cooling fans

As stated on the turbogpgarage.com website  8)
Title: 3.1 turbo hybrid in a 1990 chevrolet celebrity
Post by: Jeorge on October 05, 2002, 11:22:16 AM
and that Crank is the Same as in the Lumina APV, Pontiac Transport and olds van too.

from 90-92 3.1L

as told to me by a Cross refference to find parts.