A local buddy is parting out a wrecked GTP, and I was wondering if I should pick up the tranny for my 5 speed TGP? It's pretty much gonna be a race car (not a fast one :laugh:, but stripped down, probably running N20, etc)
I just want to know if it'll bolt up. I'm not much concerned with the fact that it's an E-HD, or the wiring or anything else. I'm thinking probably a paddle shifter. Maybe even build a shifter program that I can use to shift for me. So I can program each shifts shift point to play around with and see what kind of time differences it'll give me.
I used to know the answer to this question, but it's been awhile. And I'm getting old. Also, what's everybody's opinion on how much better (or worse) it'll hold up vs. the 4T60? Any input will be amusing.
I would say that it would bolt up to the LG5 bell housing. 96-97 Z34's with the 3.4 DOHC had 4T65HD's. All 60V6's have the same bell housing pattern, so I don't see why not.
This is what I'm hoping to hear. If nothing else it'll be a fun project. :icon_biggrin:
It will bolt up but isn't it computer controlled? How are you going to control it?
Quote from: GPChief on February 25, 2007, 11:05:53 AM
It will bolt up but isn't it computer controlled? How are you going to control it?
X2, how can you build a shifter program?
if there is a way to make it work that would be awesome, I know my GTP's transmission is a lot stronger.
Well, without being 4T65-EHD specific, I can control all the solenoids with simple 12v switches. Someone a few (4-5?) years ago built a paddle shifter this way. The "program" will be a primarily solid state circuit, using RPM switches mainly. I haven't thought much about it, as I couldn't remember if it would bolt up or not. :laugh: I need to get a diagram to see what all inputs the transmission uses for automatic operation, but as I said, it's going to be a "race" car, so manually shifting it won't be a big deal. I'll probably just have it re-built using a hi-po set of clutches for safety, then see how fast I can get those solenoids to shift. :laugh: The new Jaguar 6 speed manumatic shifts in less than .6 seconds. Let's see how the General can do. :laugh:
Tranny got delivered today, with axles, I've very curious as to whether they use the same splines, etc. I've got a TGP 4T60 sitting here that I can do ALOT of side by side with. I'm even going to test fit the axles etc. and start going over the electronics. If anybody has any info that'd be great. I'm just interested in the inputs and outputs if you know what I mean. It's a big sum-bitch that's for sure. :laugh:
Seeing as how we just got the power plant in my car today the issues that "might" arise are 1: Axle length, 2:fitments on your cradle (not much room with 4T60) 3: which flywheel / Torque converter to use 4: electronic input from the front of the 4T60 VS 4T65-HD.
Two other things to think about:
1. Manual valve body - this may enable you to do away with computer controlling the tranny
2. Change the gear ratio (much easier with the 4T60E / 4T65E / HD trannys)
Good Luck Jay!
You know the more I think about it, I'm probably going to be best off pulling the cradle out of my red TGP (the parts car) and setting it up in the garage. That way I can test fit the engine, tranny etc. without that pesky car in the way. :laugh: The axles I'm not soooo worried about, the main reason I grabbed the GTP axles is so I can use the inner joints for the tranny side, and have axles made with my TGP stock outer joints. It's really nice having Moser Engineering one county over!!! (Anybody ever heard of them? :laugh: :laugh: ;) ;) )
I can still have a TC made for it by a family friend that makes custom 'verters. Then I could even do away with the TCC and not have to worry about those electronic either.
I'm going to grab a shop manual from a GTP and isolate the complete wiring for the tranny. So I can see who talks to what. Then I can decide how to go about my custom shifting setup. I also have a father/son pair of tranny genius' that can help me with this, they have so many connections in the transmission world it's retarded. So if they don't know an answer they'll get it. I'm really starting to look forward to this.
I'm not a tranny guy, so I don't have a whole lot to offer, but I'm really curious to see how you make this work. Keep us posted. :icon_biggrin:
I'm willing to bet using the stock outer and 65-E inner axles together wouldn't be too far off from the proper length that is needed. Everyone does this with the 3800 swaps and they typically have no issues(unless the cars are lowered). Either way, axles aren't that big of a deal to overcome...
The biggest problem I see with this swap is actually controlling the transaxle properly since the 65-E does not use a vacuum modulator for line pressure(electronically controlled via a PWM solenoid as far as I know). There is also at least one more pwm solenoid in the trans for the tcc from what I remember. I have not done much research, but I am also planning to swap a 65-E HD into my car(probably sometime later this year).
I have some wiring diagrams kicking around somewhere if you need them Jay(pretty sure I have stuff that covers the 97-03 model 65-E's...).
EDIT: I forgot to mention that there is an aftermarket controller for the transaxle available from PCS, it runs about $700 though. I may end up rigging up a spare OBD-II pcm and all just control the transaxle if necessary since I can get an entire harness, pcm, etc. for cheap. :laugh:
I thought about doing that too, but does the trans need a digital input. I bet our cars can't give it one. ;) That's the only thing I'm worried about. But again, I'm not worried one bit about the electronics, to be honest, I know I can make it work. It's just a matter of how I want to do it. Cars are easy, just 12v flying around. :laugh:
And again, I'm going to get a custom converter made, pretty much to specifically get rid of the TCC. If I do run a 'verter with a clutch, it'll solely be for the reason of locking it up after launch for a better run. But I'll probably ditch it.
The problem I saw was the 65s pigtail was fighting for room with the stock x-over. The 65 e is controlled electronicly EXACLY like the late 60-e. Just that the 65-e has a presure manifold --fancy for nintendo key pad. All it does is senses pressure (much like a oil pressure switch, not a variable meter) and just goes to the PCM. The PCM then knows what the trans is doing and if its doing what it should.
YOu have a A and B shift selinoids to worry about. (upshift , downshift) Replaces Govenor.
TCC selinoid. Our ECM can controll this one though.
And PWM selinoid which controlls line pressure. I belive level 10 or Intense has a shift kit for it that will litterally make this selinoid useless. Its like unhooking the vacume modulator. The more open it its, the softer the shift..closed..its firm I belive.
Just look at a service manual for the 65es selinoid operation and you can determin a Paddle switch or toggle for the shift selinoids.
I see a Timmer IC/FET type circuit for the PWM. Something thats setup to run a transformer. Just lower the palsewith with a resistor. And then use the TPS signal to stop the palsewith (WOT) or increase/activate it (part throttle)
Good luck.
Im going the other route. Im turning a TGP trans into a F7 sorta using the 65 guts. Too bad I'll have to look into a welder if I wanto use the 65-hds' differential, carrier assym.
I was hoping you were going in get into this thread. :cheers:
As far as the pigtail, I don't mind a complete re-wire. It's a project, so that just means MORE FUN WORK! :icon_eek:
I wasn't sure if the tranny used an A-B or if it used 3-4 different solenoids to control bands/packs like Chrylser does, this makes me happy to hear. :thumb:
So if I can't/don't want to get a new 'verter I can just splice into the harness from the 60's wiring for TCC control, copy. Are they both just switched? I'd assume they don't have a PWM controlled lockup, or we'd replace them alot sooner. (Wearing clutches)
I just went over Intenses website as well as level 10 and couldn't find this shift kit you speak of. I found a shift kit on the Intense website, but don't think it's the same one. http://www.intense-racing.com/Merchant2/merchant.mvc?Screen=PROD&Product_Code=TSP-651&Category_Code=T
As far as the PWM setup, we have one we use for Subaru DCCD (Driver Controlled Center Differential) in the STi's. When you swap a 6 speed with DCCD over you have to use this to control the PWM solenoid for lockup of the center diff. What is PWM controlled on the 65-EHD? I haven't looked much into it, so I'm not sure.
Quote
Good luck.
Thanks, hopefully I won't need much of it. But I'd rather be lucky than good anyday.
The E-HD diff/carrier is 300000% the reason I'm doing this, I'm also doing it for the obvious increase in durability, but I've spilt spider gears on a track before (5 speed TGP) and my auto car is sitting in the driveway with a toasted 1st gear. The transmission is the only thing that made me not like these cars any more.
Here these might help:
89 3.1 Turbo Wiring Diagram
http://i166.photobucket.com/albums/u87/darkride2007/Diagram1.jpg
http://i166.photobucket.com/albums/u87/darkride2007/Diagram2.jpg
http://i166.photobucket.com/albums/u87/darkride2007/Diagram3.jpg
and 89 3.1 Turbo ECM Pinounts
http://i166.photobucket.com/albums/u87/darkride2007/Pinout1.jpg
http://i166.photobucket.com/albums/u87/darkride2007/Pinout2.jpg
Thanks you, I'm sure they'll come to some use. :cheers:
have you made any progress?
Not yet, I've got the tranny and the axles here. I've been driving ALL OVER the place picking stuff up for my buildup of my 500 AWHP WRX. I drove over 1000 miles in the WRX last week picking up 2 engines, a JDM Ver. 8 6 speed tranny, and some other random bits. Then I was told by my machine shop (I'm using a new one for the boxer engine in the WRX) that I couldn't even talk to anyone until Wednesday of this week, their "Suby Expert" is on vacation. :icon_evil:
I've also began construction of my new "shed" it's 10x13 and going to be wired, and maybe even throw in an air conditioner. :laugh: It's going to free up ALOT of room in my garage which is just rediculously over stuff with tools and car parts (I have 2 TGP engines, and 1 TGP tranny, along with 1 Buick 350 V8, 1 3800 series 2, a turbo 350 tranny a 700R4 tranny and a Ford 9" rear) :icon_eek: that I can barely work in there. :icon_frown:
But that will all be calming soon, and I can get some manuals etc. for this tranny and see what all the electronics are about. And when the garage is cleaned up I can bring in the new subframe from the parts TGP and mock everything up.
Delays again :icon_frown: . Hardrive crashed a while back. Then working 80+hrs a week doesn't do justice either....kinda :icon_rolleyes: .
http://www.thrashercharged.com/L67_htm/shiftkit.shtm (http://www.thrashercharged.com/L67_htm/shiftkit.shtm) Guess it wan't intense or level ten. This is the shift kit. Exacly what I did to my 3t40..just a helper spring and a washer.
If you still wan to increase line pressure you can still use a the TImmer IC circut and trottle. It'll be more civilised that way then just eliminating the PWM selinoid. I would even recomend using the circut even so since the oil pressure might be too low on some pumps for "racing".
The only thing PWM is the line pressure. The TCC is sorta also. But the only thing your eliminating by just using the TGP TCC stadagy is leaving the soft apply on the table. You might get some shutter. The friction on the ECCC torque converter is met to slip and wistands heat. I've heard of people using the ECCC torque converter on regular 3t40s and 4t60s and 60-es that don't use them and work fine. If your incline, have yours changed to red friction by a torque converter shop. The red stuff is ment to lock up with little to no slip.
Well thats the hillbilly way.